Compare the table you live with and the table you host with
| Model | Top dimensions in use | Height | Best fit for the layout |
|---|---|---|---|
| IKEA NORDEN gateleg, birch | 26, 89 or 152 × 80 cm | 74 cm | A flexible eating spot that can gain floor space when the leaves are lowered. Check where the swinging supports sit before choosing chair positions. |
| IKEA ROSENTORP extendable, white | 110 cm round, or 155 cm maximum length | 75 cm | A short daily footprint with a longer guest setting. Tape both footprints before settling on placement. |
| Castlery Seb Extendable, 190–240 cm | 190 or 240 × 100 cm | 75 cm | A larger room with clear end access. Castlery gives a 156 cm leg-to-leg gap at 45 cm height and 57 cm legroom height clearance. |
Choose by actual eating positions. A wider top helps with shared dishes, but the legs and under-table frame decide which places work. If two seats straddle a gateleg or a leaf support, check where elbows, thighs and chairs go in that exact configuration.
Tape out the table at its largest size
Mark the tabletop on the floor in both settings. Open any kitchen cabinet or fridge door that crosses the dining area. Check the main route from the kitchen to the living room while someone sits at the table. Leave enough room to pull out the actual chairs and stand up without moving another seat.
For illustration, adding 75 cm of working space to both sides of a 110 cm round table produces a 260 cm span. An 80 cm-wide rectangle with the same allowance takes 230 cm across. Seventy-five centimetres is only a layout test. Try the mock-up with chairs pulled out, and allow more space where people pass behind them or use a mobility aid.
Check leg spacing and the underside height
Measure the narrowest space between legs where the chairs sit. Three 48 cm-wide chairs total 144 cm. Inside a 156 cm opening they leave just 12 cm to divide between all gaps and the ends. Draw the chairs to scale at their widest points. For armchairs, measure from the floor to the arm’s highest point and compare it with the actual underside, apron or extension hardware.
Look at the leaf mechanism in both settings. Ask whether the leaf stores in the table, where the support sits after opening and whether one person can extend it comfortably. For a family table, check the exact care instructions for hot dishes, water rings and spills on the leaf seam.
Quote the full delivery and assembly cost
Use the largest packed piece rather than the tabletop dimensions when checking the lift and tight turns. IKEA lists NORDEN in two boxes up to 83 cm long, and the longest ROSENTORP box at 115 cm. Ask the seller for Castlery’s packed dimensions and whether legs can be fitted in the room. Check furniture delivery, stairs and access with IKEA Singapore or Castlery Singapore. Keep delivery, assembly and any chairs in the total price when comparing two tables.
Start with a daily layout and a guest layout
Draw your dining area twice, once for the people who use it every day and once for the largest gathering you plan to seat. On each drawing, mark where the fridge, kitchen or front door opens. Put the table and each chair where they will actually sit and draw a route between the rooms people use. Move the tabletop on paper before buying it. A gateleg may work tucked against a wall for breakfast and need to shift into the middle of the room before both leaves can open.
For a numerical example, say your clear dining space is 285 cm wide. An 80 cm-wide table centred across it leaves about 102.5 cm on each side before chairs. Turn the table so its 152 cm extended length spans the same width and that space drops to 66.5 cm on each side. Now set out the actual chairs and see how much space a seated guest leaves for someone to pass. The arithmetic shows why the table’s orientation matters in that room. Allow space for an actual chair pullout or any wider route needed in your household.
For a daily dining spot for two, try mock-ups of the 89 × 80 cm NORDEN with a single leaf open and the 110 cm ROSENTORP round table. Put the place settings and the dishes you usually share onto a mock-up made of paper or cardboard. Check what happens when someone sits at the end or opens the adjacent cabinet. If a chair would need to be moved every time you pass, change the layout and repeat the test.
Compare capacities by the chairs you will really use
Count people on the plan after you have measured the chairs. When using broad armchairs, the limiting dimension may be their widest point halfway up. For a bench, test whether two people can get in and out while a third stays seated. At an extendable table, place the end chairs on the floor drawing in both configurations. The support rail or leg position can move relative to a seat when the leaf opens.
The Castlery example lists a 156 cm gap between legs at a specified height. If you bring two 50 cm chairs to that side, the 100 cm occupied leaves 56 cm to divide between the chair gaps and the ends. Add a third 50 cm chair and only 6 cm remains before spacing. Compare that with placing two chairs on a side and adding end seats where knees and the legs fit. The length of the tabletop alone gives a different impression.
If someone needs wheelchair access or has a preferred transfer side, check the actual approach, underside height, knee depth and clearance around the seat in the final layout. Bring the dimensions of the chair or aid and check the widest part of the route, including turns and the approach from the front door. Ask the showroom for the underside measurement at the position they will use. For the rest of the seats, the dining chair guide shows how to compare seat and arm height.
Pick the finish for meals, homework and frequent cleaning
Ask for the material of the actual tabletop and its edge. A seller may use different names for solid wood, wood veneer or a painted finish, so match the care sheet to the exact product code. Check whether it recommends a cloth, routine treatment or protection from water and heat. Ask whether the leaf uses the same finish as the rest of the table, and whether marks on either piece can be repaired by the seller.
If the table doubles as a desk, sit with a laptop and book on a similar display table. Try typing with your elbows in a normal position and check the clearance around the apron. Think through where your power cable can reach without crossing a regularly used walkway. If a child works on the table, check how easy it is to wipe around seams and whether the open leaf creates an uneven writing surface.
For everyday meals, try a water glass, a warm serving dish and the placements you use. Do a small test on a showroom sample only if the seller permits it. At home, follow the model’s care guide and use the table protection it calls for. Storing and moving a leaf repeatedly can make its edges more vulnerable, so check how it is held when packed away.
Check the room where the largest piece will be assembled
Ask for the biggest box’s length, width, depth and weight. Compare it with the clear width and height of the lift door and the space to turn in your lift lobby. A box that fits through both openings in a straight line can still be awkward at a right-angle corner. Tell the delivery team where the turn is so it can assess the route. Mark where assembly can happen and whether it needs space to lay the table upside down.
Before disposal of the old table, open the new one through its full range and check it is stable on your floor. See whether a leaf needs two people, whether you have somewhere to store it, and how it locks closed. Record the seller’s return or collection procedure if site access raises an issue. Keep the receipt and assembly instructions for tightening joints or checking which replacement hardware to request.
Test a narrow tabletop with the food you normally serve
Lay out plates, water glasses and serving dishes on a mock-up at the table’s real width. A family that generally eats plated meals may need only a small strip in the middle. If you serve shared bowls, hotpot or several side dishes, mark the size of the largest pieces and check whether people can still reach their glasses. For an electric appliance, plan a power route that stays clear of walking areas and check the table finish’s care instructions.
When hosting six or eight, test how serving works for the people at the ends. If they need to stand each time to reach a shared dish, try spreading duplicates of small items such as condiments or using a separate serving surface. Do this test before deciding that a wider table is the only way to make the meal work.
Sources
- IKEA Singapore NORDEN gateleg table, birchLength in all three settings, height, width and carton sizes.
- IKEA Singapore ROSENTORP extendable table, whiteRound diameter, maximum length, height and packaging.
- Castlery Singapore Seb Extendable Dining Table, 190–240 cmClosed and extended dimensions, leg spacing and under-table clearance.
- IKEA Singapore deliveryFurniture delivery and access.
- Castlery Singapore deliveryDelivery, carry-up and site-access policies.